+
  • SG2200A(1).png
  • 1(1709723777834).png
  • 前.png
  • 侧.png

SG2200A


The frequency range is up to 20GHz; The high signal is pure, and the typical value of the phase noise <-115dBc/Hz@10 kHz; Support 130dB wide dynamic power adjustment output; Support various simulation modulation AM/FM/ΦM; Support pulse modulation, up to 70dB of interrupt ratio; can input pulse sequences; Provide internal modulation sources: sine waves, waves, triangular waves, sawtooth waves; Standard 2U height, convenient for rack integration; providing rack installation kit; USB/LAN remote control interface provides standard SCPI command sets.

Key words:


The SG2000 series microwave signal generator is positioned as a multi -function, cost -effective signal generator, which covers the frequency range to 20GHz. It has a variety of commonly used simulation modulation functions (AM/FM/фm), pulse modulation function, low -frequency output, low -frequency output Function and frequency scanning function. The above function makes this signal generator a flexible and general instrument, which is suitable for teaching and scientific research, product development, production and maintenance, and meets the application needs of different application scenarios. Rich logic hardware interfaces and widescreen LCD display, standard 2 U height chassis, complete standard S C p i command sets and general -purpose multi -communication modes, which brings great convenience for you to carry out remote control and secondary integration development.

Simulation modulation function with a high adjustment rate

It has the adjustment (AM), FM (FM), Primitive (ΦM) and the modulation rate can reach a maximum of 1MHz. The signal is unpleasant, supports internal and external modulation sources, and has a better performance. For application scenarios that require simulation signals, only this one requires this one requires this one. The device can be satisfied.

Powerful pulse modulation function

The ultra -long pulse cycle (400ns ~ 160s) ultra -wide pulse width (200ns ~ 85s) is as high as 70dB of a compliance ratio, which can be used to measure the characteristics of active device work under the condition of pulse signal, including T/R components on the radar on the radar And module.

Low -frequency output

Provide internal modulation sources: sine waves, waves, triangular waves.

  • Frequency range: 9kHz ~ 20GHz
  • Frequency resolution: 0.01Hz
  • Reference frequency: 10MHz
  • Temperature stability: ± 1ppm
  • Internal reference output: 10MHz, ≥+8dBm
  • Harmonics typical value: ≤ -30dBc
  • Non-harmonics typical value: ≤ -60dBc
  • SSB phase noise: -115dBc/Hz@10kHz
  • Output power range: maximum output power:+10dBm, minimum output power: -120dBm
  • Power accuracy: ± 1.0dB (typical value)
Model Name Frequency range Frequency resolution Phase noise

Output power

(indicator guarantee)

Modulation Type Communication Interface Price
SG2150A 100kHz~15GHz 0.01Hz -115dBc/Hz@10kHz -120dBm to +10dBm AM/FM/ΦM/Pulse the standard USB-HOST,USB-DEVICE,LAN and RS232 Quote
SG2200A 9kHz~20GHz 0.01Hz -115dBc/Hz@10kHz -120dBm to +10dBm AM/FM/ΦM/Pulse the standard USB-HOST,USB-DEVICE,LAN and RS232 Quote
Configuration Describe Order number
Host Microwave signal generator SG2150A/SG2200A
Standard attachment CD (user manual, programming manual)  
Power Cable (Standard AC220V power cord)  
Optional Power meter controller SG2000-PMC
Rack mount kit SG2000-RMK

Previous Page

Next Page

Previous Page

Next Page

Universal attachments (optional)

Vector Net Calibration Kit

Sagittal Net Calibration Kit (4 SAM type negative calibration pieces, DC-9GHz)

Ultra short wave handheld direction finding antenna (9kHz~8000MHz)

9KHz-30MHz handheld directional antenna 20MHz~200MHz handheld directional antenna 200MHz~500MHz handheld directional antenna 500MHz~8000MHz handheld directional antenna

LNA010 broadband amplifier

When not using a direct power cord, it is necessary to ensure that the input voltage of the broadband amplifier is+5V. When using a direct power cord, it is necessary to ensure that the input voltage of the direct power cord is+5V

PLA030 Pulse limiter

The main function of a limiter is to limit the output signal amplitude to a certain range, which means that when the input amplitude exceeds a certain reference value, the output amplitude will be limited to a certain amplitude and will no longer change with the input voltage. The applicable frequency range is 50kHz~1GHz.

RFS003 Radio frequency switch

The applicable frequency range of the RF switch (RFS003) is 9kHz~300MHz. When the RF switch is turned off, the isolation degree is 34dB (minimum value). This RF switch is mainly used in conjunction with our company's limiter.

ANT01 Near-field probe

ANT01 is a cost-effective near-field probe primarily used to locate interference sources and determine the cause of interference. It can be used to detect the direction and strength of the magnetic field on the surface of the device;

PRBI-400 Current injection probe

The current injection probe is mainly used for conducting sensitivity measurement; The interference signal is injected into the signal cable or power line of EUT to simulate external interference to determine the conduction sensitivity of EUT.

CDN016-M3 Coupling decoupling network

The coupling/decoupling  network consists of two parts: coupling and decoupling.The main  function of decoupling is to prevent useful signals from leaking to the power supply terminal (AE port) and to prevent disturbing signals from interfering with useful signals. The function of coupling is to transmit the disturbance signal of the device under test (EUT port) to the signal port.(RF port) in order to measure by measuring instruments, or transmit the electromagnetic disturbance signal of RF transmitter to the tested equipment. 

VB30 vswr bridge

• Frequencyrange: 10MHz-3.6GHz  • Tested port: N (female) type  • IN-1o-DUTinsertion loss: 4dB (typical)  • Directionality: 24dB (typical)  • Maximum input power: +30dBm(lW)  • Applicable models: HSA800 series, SAi 000 series and SA2000 series 

T/R1000 RF Demo Kit

• Radio frequency amplifier: The frequency range is 10MHz~2GHz,And the gain is 9dB~15d8(14dB@lGHz) • Radio frequency band-pass filter: Bandwidth 920MHz沉5MHz,Center frequency 922.5MHz  • Mixer: RF IN 5MHz~1500MHz             LO IN 5MHz~500MHz             RF OUT DC-1000MHz  • Oscillator LO/N:Frequency range 35MHz~4400MHz, Output power -3dBm--10dBm  •Oscillator LO:The frequency range is 2200MHz~4400MHz.,And the output power is 0dBm~+ 13dBm • Variable gain amplifier:Frequency range 15MHz~30MHz, gainrange 0dB~30dB  • Intermediate band pass filter: Bandwidth19.9MHz~22.9MHz ,Center frequency 21.4MHz • Reference timebase: 10MHz  •Interfuce:USB

FD100 frequency detection characteristic test module

• Based on BALUELEC Spectrum Analyzer, It can provide frequency discrimination   characteristic test function, Which can replace frequency scrumer  • Size 100mmx60mmx25mm • Universal USB interfuce for easy control  • Weight≤200g • Applicable models: SA1000 series and SA2000 series

DA800 directional broadband antenna

• Frequency measurement range: 600MHz-8000MHz •Input impedance: 50Ω • VSWR(Typical):<2:1 • Gain (Typical): 6dBi • Weight: 400g • Dimension: 353mrnx223mrnx28mrn

Message feedback

Welcome to leave a message online, please fill in the information according to the following form; We will contact you as soon as possible according to the information you fill in

Submit Message

Contact Us

Tel: +86-0551-68107097

Email: admin@baluelec.com

Address: No. 800, Wangjiang West Road, High-tech Zone, Hefei City, Anhui Province China.

WeChat
WeChat
Tiktok
Tiktok
Video Number
Video Number

Copyright © Baluelec

安安新材料

 Powered by: 300.cn  |  SEO   |   Business License